; CoCreate Modeling Revision 17.0
;;
;; NOTE: This file defines the contents of the Command Mini Toolbar which
;; appears after a selection during PRESELECT.
;; The commands referenced by sd-define-application-cmt-contents are
;; available commands identified by "Application" - "Group" - "Command" 
;;
;; In the Modeling application the following scenarios (identified by
;; specific keywords) are supported:
;;
;;  :2d-edge             One or more modifiable 2D geometries
;;  :2d-circular-edge    One modifiable arc or circle
;;  :faces               More than one modifiable face, radial or offset face
;;  :single-face         One modifiable face
;;  :offset-faces        More than one modifiable cone or spun-bspline faces
;;  :single-offset-face  One modifiable cone or spun-bspline face
;;  :radial-face         One modifiable radial face
;;  :blend-faces         More than one modifiable blend faces
;;  :single-blend-face   One modifiable blend face
;;  :chamfer-faces       More than one modifiable chamfer faces
;;  :single-chamfer-face One modifiable chamfer face
;;  :geometric-feature-faces 
;;                       One modifiable geometric feature
;;  :edge                One or more modifiable edges
;;  :wp                  One or more workplanes where at least the position is
;;                       allowed to be modified
;;  :wp-with-profile     One workplane with some real geometry (overlapping
;;                       loops and not closed profiles are allowed).
;;                       NOTE: If this scenario is detected, the separation of
;;                       the profile into closed loop sections is performed
;;                       automatically to be used in commands like PULL
;;  :part-assembly       One or more parts and/or assemblies where at least the
;;                       position is allowed to be modified
;;  :annotation-3d       One 3D annotation where at least the
;;                       position is allowed to be modified


(oli:sd-define-application-cmt-contents "SolidDesigner"
 :contents
 '(:2d-edge          (("SolidDesigner" "Modify 2D" "Stretch 2D CP")
                      ("-")
                      ("SolidDesigner" "Modify 2D" "Move 2D CP")
                      ("SolidDesigner" "Modify 2D" "Copy 2D")
                      ("SolidDesigner" "Modify 2D" "Rotate 2D"))
   :2d-circular-edge (("SolidDesigner" "Modify 2D" "Change Radius 2D")
                      ("-")
                      ("SolidDesigner" "Modify 2D" "Stretch 2D CP")
                      ("SolidDesigner" "Modify 2D" "Move 2D CP")
                      ("SolidDesigner" "Modify 2D" "Copy 2D"))
   :faces            (("SolidDesigner" "Modify 3D" "Move 3D")
                      ("-")
                      ("SolidDesigner" "Modify 3D" "Stretch")
                      ("SolidDesigner" "Modify 3D" "Offset")
					  ("SolidDesigner" "Modify 3D" "Align")
					  ("-")
					  ("SolidDesigner" "Modify 3D" "Linear Pull Faces")
                      ("SolidDesigner" "Modify 3D" "Angular Pull Faces")
                      ("-")
                      ("SolidDesigner" "Modify 3D" "Cut Faces")						  
                      ;;("SolidDesigner" "Modify 3D" "Taper")	
                     )
   :cone-spun-faces  (("SolidDesigner" "Modify 3D" "Offset")
                      ("-")
                      ("SolidDesigner" "Modify 3D" "Move 3D")
                      ;;("SolidDesigner" "Modify 3D" "Taper")	
					  )	
   :radial-face      (("SolidDesigner" "Modify 3D" "Change Radius")
                      ("SolidDesigner" "Modify 3D" "Move 3D")
                      ("-")
                      ("SolidDesigner" "Workplane" "New WP on Face"))
   :blend-faces      (("SolidDesigner" "Modify 3D" "Blend Modify")
                      ("SolidDesigner" "Modify 3D" "Blend Remove"))
   :chamfer-faces    (("SolidDesigner" "Modify 3D" "Chamfer Modify")
                      ("SolidDesigner" "Modify 3D" "Chamfer Remove"))
   :geometric-feature-faces
                     (("SolidDesigner" "Modify 3D" "Move 3D")
                      ("SolidDesigner" "Modify 3D" "Cut Faces")
                      ("SolidDesigner" "Modify 3D" "Copy Faces")
                      ("-")
                      ("SolidDesigner" "Modify 3D" "Stretch")
                      ("SolidDesigner" "Modify 3D" "Linear Pull Faces")
                      ("SolidDesigner" "Modify 3D" "Angular Pull Faces")
                      ("-")
                      ("SolidDesigner" "Modify 3D" "Offset")
                      ("SolidDesigner" "Modify 3D" "Taper")
                      ("SolidDesigner" "Modify 3D" "Align"))
   :cylinder-face    (("SolidDesigner" "Modify 3D" "Change Radius")
                      ("-")
                      ("SolidDesigner" "Modify 3D" "Stretch")
					  ("SolidDesigner" "Modify 3D" "Move 3D")
					  ("SolidDesigner" "Modify 3D" "Offset")     
					  ("SolidDesigner" "Modify 3D" "Align")		
                      ("-")
                      ("SolidDesigner" "Measure" "Clipped Cross Section") 
					  ("-")
					  ("SolidDesigner" "Modify 3D" "Cut Faces")
                      ;;("SolidDesigner" "Modify 3D" "Taper")	
					  )
   :planar-face      (("SolidDesigner" "Modify 3D" "Move 3D")
                      ("-")
                      ("SolidDesigner" "Modify 3D" "Stretch")
                      ("SolidDesigner" "Modify 3D" "Align")
				      ("SolidDesigner" "Modify 3D" "Linear Pull Faces")
                      ("SolidDesigner" "Modify 3D" "Angular Pull Faces")
                      ("-")
                     ;; ("SolidDesigner" "Modify 3D" "Taper")		
                      ("SolidDesigner" "Workplane" "New WP on Face and Project Constr")  
					  ("SolidDesigner" "Measure" "Clipped Cross Section")			 
					  ("-")
					  ("SolidDesigner" "Modify 3D" "Cut Faces")					
					  )
   :edge             (("SolidDesigner" "Modify 3D" "Create Const Radius Blend")
                      ;;("SolidDesigner" "Modify 3D" "Create Var2 Radius Blend")	
                      ;;("SolidDesigner" "Modify 3D" "Create Varn Radius Blend")	
                      ("-")
                      ("SolidDesigner" "Modify 3D" "Create Const Dist Chamfer")
					  ("SolidDesigner" "Modify 3D" "Create Dist Dist Chamfer")		
					  ("SolidDesigner" "Modify 3D" "Create Dist Angle Chamfer")		
					  )
   :single-wp        (("SolidDesigner" "2D CoPilot" "Line/Arc")
                      ("SolidDesigner" "2D CoPilot" "Rectangle")
                      ("SolidDesigner" "2D CoPilot" "Circle")
                      ("-")
                      ("SolidDesigner" "Workplane" "Position WP"))
   :wps              (("SolidDesigner" "Workplane" "Position WP"))
   :single-wp-with-profile  
                     (("SolidDesigner" "Machine" "Linear Pull Profile")
                      ("SolidDesigner" "Machine" "Angular Pull Profile")
                      ("SolidDesigner" "Machine" "New Punch")
                      ("SolidDesigner" "Machine" "New Stamp")
                      ("-")
                      ("SolidDesigner" "2D CoPilot" "Line/Arc")
                      ("SolidDesigner" "2D CoPilot" "Rectangle")
                      ("SolidDesigner" "2D CoPilot" "Circle")
                      ("-")
                      ("SolidDesigner" "Workplane" "Position WP"))
   :part-assembly    (("SolidDesigner" "Part and Assy" "Position Dynamic")
                      ("-")
                      ("SolidDesigner" "Part and Assy" "Copy Part/Assy")
                      ("SolidDesigner" "Part and Assy" "Share Part/Assy")
					  ("SolidDesigner" "Modify 3D" "Mirror")			
					  ("SolidDesigner" "Delete" "Delete 3D")			
					  ("-")
					  ("SolidDesigner" "Drawlist" "Draw Only in New VP ...")	
					  ("-")
					  ("SolidDesigner" "Eigene Befehle" "Zeichnungsstatus")	
					  ("SolidDesigner" "Eigene Befehle" "Teilestammeditor") 
					  )
   :face-part        (("SolidDesigner" "Part and Assy" "Position Dynamic")
                      ("-")
                      ("SolidDesigner" "Modify 3D" "Paste")
                      ("SolidDesigner" "Surfacing" "Grow Surface")
                      ("-")
                      ("SolidDesigner" "Part and Assy" "Copy Part/Assy")
                      ("SolidDesigner" "Part and Assy" "Share Part/Assy"))
   :single-part      (("SolidDesigner" "Part and Assy" "Position Dynamic")
                      ;;("-")								
                      ;;("SolidDesigner" "Machine" "Shell")			
                      ;;("SolidDesigner" "Machine" "Unite")			
                      ;;("SolidDesigner" "Machine" "Subtract")		
                      ("-")
                      ("SolidDesigner" "Part and Assy" "Set Active Part")	
					  ("-")
					  ("SolidDesigner" "Part and Assy" "Copy Part/Assy")
                      ("SolidDesigner" "Part and Assy" "Share Part/Assy")
					  ("SolidDesigner" "Modify 3D" "Mirror")			   
					  ("SolidDesigner" "Delete" "Delete 3D")			    
					  ("-")
					  ("SolidDesigner" "Drawlist" "Draw Only in New VP ...")	
					  ("-")
					  ("SolidDesigner" "Eigene Befehle" "Zeichnungsstatus") 
					  ("SolidDesigner" "Eigene Befehle" "Teilestammeditor")
					  )
   :annotation-3d    (;; for driving dimensions the system automatically
                      ;; adds the corresponding Modeling command (e.g. Move 3D)
		      ("-")
                      ("SolidDesigner" "3D Documentation" "Move Anno")
                      ("SolidDesigner" "3D Documentation" "Delete Anno"))
   )
 )