/COM,ANSYS RELEASE 11.0 UP20070125 09:44:17 12/21/2009 *** WARNING *** CP = 0.641 TIME= 09:44:18 Use of the -M switch is no longer recommended for normal ANSYS use. ANSYS now dynamically allocates memory as needed. Only use the -M switch if you are certain that you need to do so. *** WARNING *** CP = 20.203 TIME= 09:44:58 Using 1 iteration per substep may result in unconvergent solutions for nonlinear analysis and the program may not indicate divergence in this case. Check your results. *** WARNING *** CP = 20.203 TIME= 09:44:58 Temperature dependent properties have not been specified. THOPT,QUASI option does not perform equilibrium iterations, small time steps may be required to obtain accurate results. *** WARNING *** CP = 21.156 TIME= 09:45:01 Element shape checking is currently inactive. Issue SHPP,ON or SHPP,WARN to reactivate, if desired. *** WARNING *** CP = 23.422 TIME= 09:45:04 Material number 71 (used by element 182054 ) should normally have at least one MP or one TB type command associated with it. Output of energy by material may not be available. *** WARNING *** CP = 38.750 TIME= 09:45:21 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.766 TIME= 09:45:21 The detected penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 38.781 TIME= 09:45:21 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.781 TIME= 09:45:21 The initial penetration/gap is relatively large. Using bonded/no separation option may cause an accuracy issue. You may use the CNCHECK,ADJUST command to move the contact nodes towards the target surface. *** WARNING *** CP = 38.781 TIME= 09:45:21 The closed gap/penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 38.781 TIME= 09:45:21 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.797 TIME= 09:45:21 No contact was detected for this contact pair (ID= 76). *** WARNING *** CP = 38.797 TIME= 09:45:22 No contact was detected for this contact pair (ID= 77). *** WARNING *** CP = 38.812 TIME= 09:45:22 The closed gap/penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 38.812 TIME= 09:45:22 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.828 TIME= 09:45:22 The closed gap/penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 38.828 TIME= 09:45:22 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.828 TIME= 09:45:22 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.828 TIME= 09:45:22 The closed gap/penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 38.828 TIME= 09:45:22 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.828 TIME= 09:45:22 The closed gap/penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 38.828 TIME= 09:45:22 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.828 TIME= 09:45:22 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.828 TIME= 09:45:22 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.844 TIME= 09:45:22 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.844 TIME= 09:45:22 The initial penetration/gap is relatively large. Using bonded/no separation option may cause an accuracy issue. You may use the CNCHECK,ADJUST command to move the contact nodes towards the target surface. *** WARNING *** CP = 38.844 TIME= 09:45:22 The closed gap/penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 38.844 TIME= 09:45:22 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.844 TIME= 09:45:22 The closed gap/penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 38.844 TIME= 09:45:22 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.844 TIME= 09:45:22 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.844 TIME= 09:45:22 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.859 TIME= 09:45:22 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.859 TIME= 09:45:23 The initial penetration/gap is relatively large. Using bonded/no separation option may cause an accuracy issue. You may use the CNCHECK,ADJUST command to move the contact nodes towards the target surface. *** WARNING *** CP = 38.859 TIME= 09:45:23 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.859 TIME= 09:45:23 The initial penetration/gap is relatively large. Using bonded/no separation option may cause an accuracy issue. You may use the CNCHECK,ADJUST command to move the contact nodes towards the target surface. *** WARNING *** CP = 38.859 TIME= 09:45:23 The closed gap/penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 38.859 TIME= 09:45:23 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.859 TIME= 09:45:23 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.859 TIME= 09:45:23 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.859 TIME= 09:45:23 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.859 TIME= 09:45:23 The initial penetration/gap is relatively large. Using bonded/no separation option may cause an accuracy issue. You may use the CNCHECK,ADJUST command to move the contact nodes towards the target surface. *** WARNING *** CP = 38.859 TIME= 09:45:23 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.859 TIME= 09:45:23 The initial penetration/gap is relatively large. Using bonded/no separation option may cause an accuracy issue. You may use the CNCHECK,ADJUST command to move the contact nodes towards the target surface. *** WARNING *** CP = 38.875 TIME= 09:45:23 The closed gap/penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 38.875 TIME= 09:45:23 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.875 TIME= 09:45:23 The detected penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 38.875 TIME= 09:45:23 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.891 TIME= 09:45:23 The initial penetration/gap is relatively large. Using bonded/no separation option may cause an accuracy issue. You may use the CNCHECK,ADJUST command to move the contact nodes towards the target surface. *** WARNING *** CP = 38.891 TIME= 09:45:23 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.891 TIME= 09:45:23 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.891 TIME= 09:45:23 The initial penetration/gap is relatively large. Using bonded/no separation option may cause an accuracy issue. You may use the CNCHECK,ADJUST command to move the contact nodes towards the target surface. *** WARNING *** CP = 38.891 TIME= 09:45:24 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.891 TIME= 09:45:24 The initial penetration/gap is relatively large. Using bonded/no separation option may cause an accuracy issue. You may use the CNCHECK,ADJUST command to move the contact nodes towards the target surface. *** WARNING *** CP = 38.953 TIME= 09:45:24 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.969 TIME= 09:45:24 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.969 TIME= 09:45:24 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.984 TIME= 09:45:24 The closed gap/penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 38.984 TIME= 09:45:24 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.984 TIME= 09:45:24 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.984 TIME= 09:45:24 The detected penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 38.984 TIME= 09:45:24 The closed gap/penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 38.984 TIME= 09:45:24 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 38.984 TIME= 09:45:24 The initial penetration/gap is relatively large. Using bonded/no separation option may cause an accuracy issue. You may use the CNCHECK,ADJUST command to move the contact nodes towards the target surface. *** WARNING *** CP = 38.984 TIME= 09:45:24 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.000 TIME= 09:45:24 The closed gap/penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 39.016 TIME= 09:45:24 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.031 TIME= 09:45:24 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.031 TIME= 09:45:24 The closed gap/penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 39.031 TIME= 09:45:24 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.047 TIME= 09:45:24 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.062 TIME= 09:45:25 The detected penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 39.062 TIME= 09:45:25 The closed gap/penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 39.062 TIME= 09:45:25 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.062 TIME= 09:45:25 The initial penetration/gap is relatively large. Using bonded/no separation option may cause an accuracy issue. You may use the CNCHECK,ADJUST command to move the contact nodes towards the target surface. *** WARNING *** CP = 39.062 TIME= 09:45:25 The detected penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 39.062 TIME= 09:45:25 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.062 TIME= 09:45:25 The initial penetration/gap is relatively large. Using bonded/no separation option may cause an accuracy issue. You may use the CNCHECK,ADJUST command to move the contact nodes towards the target surface. *** WARNING *** CP = 39.062 TIME= 09:45:25 The detected penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 39.062 TIME= 09:45:25 The closed gap/penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 39.062 TIME= 09:45:25 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.062 TIME= 09:45:25 The initial penetration/gap is relatively large. Using bonded/no separation option may cause an accuracy issue. You may use the CNCHECK,ADJUST command to move the contact nodes towards the target surface. *** WARNING *** CP = 39.078 TIME= 09:45:25 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.078 TIME= 09:45:25 The closed gap/penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 39.078 TIME= 09:45:25 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.078 TIME= 09:45:25 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.078 TIME= 09:45:25 The detected penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 39.078 TIME= 09:45:25 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.078 TIME= 09:45:25 The initial penetration/gap is relatively large. Using bonded/no separation option may cause an accuracy issue. You may use the CNCHECK,ADJUST command to move the contact nodes towards the target surface. *** WARNING *** CP = 39.078 TIME= 09:45:25 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.078 TIME= 09:45:25 No contact was detected for this contact pair (ID= 163). *** WARNING *** CP = 39.109 TIME= 09:45:26 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.109 TIME= 09:45:26 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.109 TIME= 09:45:26 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.141 TIME= 09:45:26 No contact was detected for this contact pair (ID= 176). *** WARNING *** CP = 39.141 TIME= 09:45:26 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.156 TIME= 09:45:26 The closed gap/penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 39.156 TIME= 09:45:26 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.172 TIME= 09:45:26 The closed gap/penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 39.172 TIME= 09:45:26 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.250 TIME= 09:45:26 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.250 TIME= 09:45:26 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.266 TIME= 09:45:27 No contact was detected for this contact pair (ID= 230). *** WARNING *** CP = 39.266 TIME= 09:45:27 No contact was detected for this contact pair (ID= 231). *** WARNING *** CP = 39.266 TIME= 09:45:27 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.266 TIME= 09:45:27 No contact was detected for this contact pair (ID= 247). *** WARNING *** CP = 39.281 TIME= 09:45:27 No contact was detected for this contact pair (ID= 266). *** WARNING *** CP = 39.281 TIME= 09:45:27 No contact was detected for this contact pair (ID= 267). *** WARNING *** CP = 39.281 TIME= 09:45:27 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.297 TIME= 09:45:27 The closed gap/penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 39.297 TIME= 09:45:27 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.328 TIME= 09:45:27 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.359 TIME= 09:45:27 The closed gap/penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 39.359 TIME= 09:45:27 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.359 TIME= 09:45:27 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.359 TIME= 09:45:27 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.359 TIME= 09:45:28 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.359 TIME= 09:45:28 The closed gap/penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 39.359 TIME= 09:45:28 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.375 TIME= 09:45:28 The closed gap/penetration is larger than the pair based pinball. Please verify the pinball carefully. *** WARNING *** CP = 39.375 TIME= 09:45:28 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.391 TIME= 09:45:28 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 39.391 TIME= 09:45:28 The closed gap/penetration may be too large. Increase pinball if it is a true closed gap/penetration. Decrease pinball if it is a false one. *** WARNING *** CP = 886.188 TIME= 10:04:32 Material number 71 (used by element 182054 ) should normally have at least one MP or one TB type command associated with it. Output of energy by material may not be available. *** WARNING *** CP = 2774.172 TIME= 10:45:53 Material number 71 (used by element 182054 ) should normally have at least one MP or one TB type command associated with it. Output of energy by material may not be available. *** WARNING *** CP = 3575.812 TIME= 11:03:26 Material number 71 (used by element 182054 ) should normally have at least one MP or one TB type command associated with it. Output of energy by material may not be available. *** WARNING *** CP = 4380.719 TIME= 11:21:02 Material number 71 (used by element 182054 ) should normally have at least one MP or one TB type command associated with it. Output of energy by material may not be available. *** WARNING *** CP = 5129.719 TIME= 11:37:21 Material number 71 (used by element 182054 ) should normally have at least one MP or one TB type command associated with it. Output of energy by material may not be available. *** WARNING *** CP = 5936.609 TIME= 11:54:57 Material number 71 (used by element 182054 ) should normally have at least one MP or one TB type command associated with it. Output of energy by material may not be available. *** WARNING *** CP = 6681.469 TIME= 12:11:11 Material number 71 (used by element 182054 ) should normally have at least one MP or one TB type command associated with it. Output of energy by material may not be available. *** WARNING *** CP = 7431.328 TIME= 12:27:28 Material number 71 (used by element 182054 ) should normally have at least one MP or one TB type command associated with it. Output of energy by material may not be available. *** WARNING *** CP = 8188.391 TIME= 12:43:49 Material number 71 (used by element 182054 ) should normally have at least one MP or one TB type command associated with it. Output of energy by material may not be available. *** WARNING *** CP = 8788.406 TIME= 12:56:43 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.406 TIME= 12:56:43 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.406 TIME= 12:56:43 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.406 TIME= 12:56:43 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.406 TIME= 12:56:43 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.406 TIME= 12:56:43 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.406 TIME= 12:56:43 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.406 TIME= 12:56:43 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.406 TIME= 12:56:43 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.406 TIME= 12:56:43 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.406 TIME= 12:56:43 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.406 TIME= 12:56:43 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.406 TIME= 12:56:43 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.406 TIME= 12:56:43 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.406 TIME= 12:56:44 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.406 TIME= 12:56:44 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.406 TIME= 12:56:44 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.406 TIME= 12:56:44 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.406 TIME= 12:56:44 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.406 TIME= 12:56:44 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.406 TIME= 12:56:44 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.406 TIME= 12:56:44 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.406 TIME= 12:56:44 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.406 TIME= 12:56:44 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.406 TIME= 12:56:44 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.406 TIME= 12:56:44 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.406 TIME= 12:56:45 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.422 TIME= 12:56:45 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.422 TIME= 12:56:45 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.422 TIME= 12:56:45 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.422 TIME= 12:56:45 An error has occurred writing to the file = 16 which may imply a full disk. The system I/O error = 28. Please refer to your system documentation on I/O errors. *** WARNING *** CP = 8788.422 TIME= 12:56:45 An error has occurred writing to the file = 16 which may imply a full